FEX_ENABLEAVX was removed. Settings for host features should use
FEX_HOSTFEATURES but actually FEX_HOSTFEATURES=enableavx has different
behaviour, so we don't enable it.
This unit test hasn't really served any purpose for a while now and
mostly just causes pain when reworking things in the IR.
Just remove the IRLoader, its unit tests, the github action steps and
the public FEXCore interface to it. Since it isn't used by anything
other than Thunks.
Also moves some IR definitions from the public API to the backend.
We only used this so that our Xavier CI system which were running old
kernels could run unit tests. We have now removed the Xaviers from CI
and this is no longer necessary.
Stop pretending that we support kernels older than 5.0 and allowing this
fallback.
The 32-bit allocator is still used for the MAP_32BIT mmap flag, so the
load bearing code can't be fully removed. Just remove the config and the
frontend things using it.
It is scarcely used today, and like the x86 jit, it is a significant
maintainence burden complicating work on FEXCore and arm64 optimization. Remove
it, bringing us down to 2 backends.
1 down, 1 to go.
Some interpreter scaffolding remains for x87 fallbacks. That is not a problem
here.
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Usually uploading of results takes about two seconds.
Sometimes github's connection to the runner flakes and it stalls out the
upload action for some reason.
Github's default timeout is SIX HOURS.
Change this to a one-minute timeout on the upload step so it quickly
goes away when Github's internet flakes out.
All of these IR operations were being fairly inefficient in their
address calculation. All of these are known using power of 2 stride
indexing. So all of these can be converted from three instructions to
one.
These are always used for x87 stack accesses so each one gets an
improvement.
Before:
```asm
0x0000ffff6a800248 d2800200 mov x0, #0x10
0x0000ffff6a80024c 9b007e80 mul x0, x20, x0
0x0000ffff6a800250 8b000380 add x0, x28, x0
0x0000ffff6a800254 fd417805 ldr d5, [x0, #752]
```
After:
```asm
0x0000ffff91e80240 8b141380 add x0, x28, x20, lsl #4
0x0000ffff91e80244 fd417805 ldr d5, [x0, #752]
```
Removes some annotation warnings that have been showing up on the
actions results page.
v2 is deprecated so going to v3 is necessary. Apparently this upgrades
from Node.js 12 to 16.
Some of the unit tests we run will leak shm regions. Presumably this is
because they never called `shmctl(IPC_RMID)` so the ID is laked forever.
This can be seen by querying `/proc/sysvipc/shm` to see a list of old
shm regions that eventually hit the maximum capacity of 4096 shm ids.
Once CI is done running, run a utility application that all it does is
check for SHM IDs that have zero attachments (thus unused), it was
created by the UID of the runner, and it is older than ten minutes. At
which point it will erase it.
This will fix spurious failures in our CI caused by running out of SHM
IDs, previously I had a cron job setup to restart the CI runners every
hour or so which caused its own spurious failure problems.
FINALLY this bug was triaged which has been annoying us for...years?
The dispatcher was saving AVX state even though FEX doesn't support it
currently. This is due to it checking for the config option rather than
the HostFeatures option.
The `EnableAVX` config option is supposed to be used to inform FEXCore
if we want AVX disabled or not when the host supports the feature. In
this case it is universally enabled because we haven't encountered any
games that have issues with AVX state being saved with signals. (We know
they exist, we just don't have configurations for them).
The HostFeatures option `SupportsAVX` is the option that is supposed to
be getting used for determining if the runtime AVX feature is enabled.
This also had an issue though that this was **also** always enabled if
running on an x86 host with AVX, or an ARM host with SVE2-256bit.
It was then disabled if the config option was disabled; But, since
FEX-Emu doesn't support AVX fully yet, we need to ensure this isn't yet
enabled.
But this only solves half the problem. In order for our CI to test AVX
features before fully supporting AVX, it needs to be able to enable AVX
so that the CPU state is correctly saved.
So we need to change the default configuration option to be false, and
have CI enable it for the tests that matter before AVX is fully
implemented.
This is the bare minimum, it only tests glxinfo and vulkaninfo with and
without thunks. Nothing more special than that. Already found the .1 bug
with libvulkan host library loading.
build folder doesn't exist on a freshly started runner.
Executing the rootfs fetch script doesn't care what the working
directory is. Doesn't need to be in `build/` which doesn't exist on a
fresh runner and will fail chdir.
By default we won't build with the interpeter to reduce user confusion.
The interpreter isn't really useful to end users so remove it.
Completely removes it from building except for the fallback operations.
This also removes the selection from FEXConfig to remove selection
confusion there.
File Stats:
FEXLoader Size with Interpreter: 3422768 bytes
FEXLoader Size without Interpreter: 3301944 bytes
Size difference: 96.4699915%
Bytes removed: 120824 bytes
4k pages removed: 29.498046875 -> 30 rounded up
VM Stats (Reported from bloaty):
Memory Size with Interpreter: 6.50Mi
Memory Size without Interpreter: 6.38Mi
Size difference: 98.1538462%
Lets users know that x86-64 isn't our optimal target but can still be used if passed in a new cmake argument.
Easy enough just pass in -DENABLE_X86_HOST_DEBUG=True to cmake.
Closes#776
Passes the log movement stage to clean up the output.
Really it is only the first unit test stage that is failing, but each
subsequent log run will have failed to move since the previous stage
didn't run.
Makes it easier to scan over a failure as only the first unit test
failure step.
We have hit issues where the non-clean folder would end up leaving
artifacts which allowed tests to pass.
Remove the build folder on each run to clean up
We want to see the output from all of our runners.
Usually the x86 runner quickly spins through things and then we never see the ARM results if that side failed.
Paulo Matos