A user on a fresh install got "Calibration failed: only 0 of 21 dots" with
no reason. The installer never installed our tracker, so gaze used
SteamVR's, and the only way SteamVR's tracker rejects a dot is losing an
eye for most of the look. The panel just showed a red ring.
- install.sh: step 9/10 installs our tracker (gaze/tracker/install.sh)
after gaze mode, yes by default; it needs sudo, so --yes runs it only
when sudo won't prompt. If it fails, gaze keeps SteamVR's tracker.
Configs that still say GAZE_TRACKER=steam (the old template) are asked
whether to switch.
- GAZE_TRACKER=auto, the new default: ours when it's installed (the
frame grabber, its unit, and ft-eyes' Python), else SteamVR's.
ft-gazed rechecks every second, so installing it switches over. Input
Settings lists Own tracker first as recommended, and says how to
install it when it's missing (checking the host's /etc through
/run/host from the dev container).
- The calibration panel has a note line, orange over the instructions:
why a dot wasn't taken (an eye lost, a blink, the eyes disagreeing for
SteamVR's tracker, from steady_samples' new drop counts; ft-eyes' reply
for ours), what a click is still waiting for after 1.5 s, and a failed
calibration's most common reason, which the Gaze page shows too.
steady_samples keeps the same samples as before (checked on 2037
windows of recordings); a lost eye is named before a blink, since its
openness reads 0.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Turning gaze mode on without a calibration opened Calibrate only on the
off-to-on change, and only if it could open right then. With the headset
off, the eye tracker silent, or the panel not built, or with gaze mode
already on when the gaze service started, nothing opened and nothing said
why: the pointer just stayed a mouse.
- The gaze service now checks every second: gaze mode on, no calibration
for the tracker in use, eyes seen -> the full calibration opens. One
that closes unfinished opens again only after the headset comes off and
on, gaze mode off and on, or Calibrate, so it doesn't loop. A start that
fails retries every 10 s.
- Its status says why gaze mode can't work yet (checks.problem): not
calibrated and opening, open, closed unfinished, or can't open and why.
- Input Settings shows that under the Gaze pointer switch, along with the
gaze service not installed or not running and our tracker missing its
frame grabber.
- ft-gazectl on notes a missing calibration.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The panel drew each picture with SetOverlayRaw, a new texture upload every
time: the full calibration's 1024x768 picture flickered on every change, and
in a live test the headset kept showing the last calibration picture after the
panel had drawn the fit check (2026-10-01). Now, as screens/keyboard.cpp does,
it writes into three linear DMA-BUFs SteamVR imported once (the size of the
biggest panel; texture bounds show the part in use) and switches between them.
A show makes the overlay visible once its first picture is in.
The full calibration's and the five-dot check's dots wait for a left click or
Meta+J while you look at the dot, in place of capturing any steady gaze (which
can be a look somewhere else); no capture ring, no 8 s skip, and the check
closes after 2 minutes without a click. The quick check still captures itself.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Check headset fit now runs in the headset panel too ("fitcheck"): a card per
eye (tracked or lost, the tracker's signal, how much of the last 10 s it was
seen) and the hints, from the probe's fitcheck.py, updated at most twice a
second; left click or Meta+J runs its guided check, right click or Meta+K closes
it. So Quick check, Calibrate, and Check headset fit all happen in one place.
The gaze probe moves to the Gaze page's overflow menu as "Gaze probe
(development)", and its app menu entry says it's a development tool. Texts that
sent users to it ("use Calibrate… with Own tracker") point at Calibrate.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Drops the quick check's second step (3629681): the user didn't want it, and it
re-entered itself every tick, re-placing and redrawing the panel, which
flickered in the headset.
POINTER_GAZE_NUDGE_MAX is the one learning limit, now 55 degrees by default:
half of the 109 the Frame shows across. The helper measures the correction
itself (raw gaze to click), not the mouse's path; past the limit it isn't
learned and the helper sends "recheck" for the quick check, for the mouse and
keyboard alike. ft-gazed's own limits (8 and 25) follow the setting.
Test, our tracker's 409 clicks since its Sep 29 calibration: a one-dot check
set from any one of them puts the next 2 minutes' clicks within 15 degrees (99%
within 4.2) and the next 10 minutes' within 25, so it gets well under 55.
The panel's dot is still and its capture ring fills in quarters, so it's drawn
again only a few times per dot.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
After the quick check's capture, in gaze mode, the dot stays where it is in the
room (the panel's new "lock") and the gaze has the pointer again. You put the
pointer on the dot as you'd correct a click, with the mouse or Meta+J and the
head. That click clicks nothing: the helper sends it as "calverify", learned
whatever its size. Over POINTER_GAZE_NUDGE_MAX, the capture runs again, up to
3 times. A right click or Meta+K skips it.
POINTER_GAZE_NUDGE_MAX is now the one limit: 15 degrees by default (was 8),
and ft-gazed's own limits (8 for SteamVR's tracker, 25 for ours) follow it. A
keyboard correction past it isn't learned but opens a quick check ("recheck"),
in place of the 30 degree keyboard limit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Steam's eyetracking.txt writes "HMD on" every minute or so with nobody in the
headset, and SteamVR said it was worn for 12 hours straight, so the quick check
opened about 40 times an hour at an empty headset. It now opens when SteamVR's
tracker sees eyes for 3 s after none for 3 s, and closes when they're gone 2 s.
The log reader also drops repeated "HMD on" lines and sub-second offs, so
lessons stop counting as from an older wear every minute.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ft-gazepanel (gaze/panel) is a SteamVR overlay that stays put in your view and
shows dots at known head-relative directions; the gaze service runs it and
drives it (gaze/gazecheck.py):
- a one-dot quick check 3 s after the headset goes on, when our tracker asks
for a click (reseat), at most every 2 minutes, and from Quick check on the
Gaze page; five dots follow if the next 3 lessons are still over 2 degrees off
- the full calibration (the probe's three rounds, dark to bright) when gaze mode
comes on without one, or from Calibrate; quitting it with still no calibration
turns gaze mode off
Each dot takes the gaze once it has held still for 0.6 s; a left click or Meta+J
takes it at once, a right click or Meta+K closes the panel (the pointer helper
hides its dot and passes those presses on while "calpanel" lasts). Our tracker
gets clicks and its own calibration; SteamVR's gets lessons per eye, or a new
calibration.json.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
