Mark head follow as experimental

It works but is only lightly tested, and what's left is mostly tuning its
settings. Frametop Input Settings now says so under the Head follow switch,
and the README, design notes, and button action name say it too.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

docs/design.md

@@ -80,7 +80,7 @@ A few overlays need special handling:
 - Just off a panel, the cursor stays on that panel's plane within `POINTER_EDGE_REACH`, so resize margins and window controls just outside the panel are reachable.
 - While the left button is held, the cursor keeps the distance it had at the press and stops re-testing collisions, so dragging past a panel's edge doesn't make it jump.
 
-Head follow is off by default. With it on (`POINTER_FOLLOW=1`, or a mouse button mapped to Head follow on/off), the cursor rides on a reference direction, where you were facing when your head last settled, and keeps its offset from it. The mouse can put the cursor anywhere up to `POINTER_FOLLOW_REACH` (70 degrees) from the reference, a corner of your view included. While your head stays within `POINTER_LEASH_DEG` of the reference, nothing moves on its own. Once your head has been past the leash for `POINTER_LEASH_DELAY` (0.2 s, so a glance out and back doesn't count), the reference eases to where you're facing (time constant `POINTER_LEASH_RETURN`, 0.2 s), never falling further behind than the leash, and the cursor ends up back where it was in your view. Then it waits for the leash again. Two earlier versions didn't work out. Moving the reference only while your head pulled at the end of the leash left it up to the leash off after you turned back, and getting it centred again meant overshooting with your head. Easing it toward your facing all the time moved the cursor on every small head movement. A leash of 0 makes the reference your facing direction, so the cursor is locked to your view, and mouse movement shifts it within the view. Head roll is ignored, so tilting your head doesn't swing the cursor around. While the left button is held the cursor stays put in the room, so your head can't nudge a click or a drag. When you let go, it carries on from where it is instead of jumping.
+Head follow is experimental and off by default. It works, but it's only lightly tested, and the feel is mostly a matter of its settings; polishing it is left open. With it on (`POINTER_FOLLOW=1`, or a mouse button mapped to Head follow on/off), the cursor rides on a reference direction, where you were facing when your head last settled, and keeps its offset from it. The mouse can put the cursor anywhere up to `POINTER_FOLLOW_REACH` (70 degrees) from the reference, a corner of your view included. While your head stays within `POINTER_LEASH_DEG` of the reference, nothing moves on its own. Once your head has been past the leash for `POINTER_LEASH_DELAY` (0.2 s, so a glance out and back doesn't count), the reference eases to where you're facing (time constant `POINTER_LEASH_RETURN`, 0.2 s), never falling further behind than the leash, and the cursor ends up back where it was in your view. Then it waits for the leash again. Two earlier versions didn't work out. Moving the reference only while your head pulled at the end of the leash left it up to the leash off after you turned back, and getting it centred again meant overshooting with your head. Easing it toward your facing all the time moved the cursor on every small head movement. A leash of 0 makes the reference your facing direction, so the cursor is locked to your view, and mouse movement shifts it within the view. Head roll is ignored, so tilting your head doesn't swing the cursor around. While the left button is held the cursor stays put in the room, so your head can't nudge a click or a drag. When you let go, it carries on from where it is instead of jumping.
 
 Replacing a loaded driver's files, as re-running the installer used to do, leaves SteamVR honoring the virtual controller's hand role but not its laser claim: the dashboard pointer stays unassigned until SteamVR restarts. The driver installer now leaves an unchanged driver in place.