Screens: in games, pointing a controller at a panel turns its laser on

SteamVR's own floating windows take the laser while a controller points
at them in a game and give it back when it points away. Frametop's
panels didn't: with the controllers left to the game (outside_games, the
default, or dashboard), they couldn't be clicked without the dashboard.

ft-screens now sets MakeOverlaysInteractiveIfVisible on a screen or
floating window while a hand controller's laser pose meets it, its
controls, or its popups (UpdateAim; curved screens hit on their
cylinder), and clears it 0.3 s after the aim leaves a wider margin. A
drag or a held button keeps it on. The keyboard, one overlay, uses
ComputeOverlayIntersection and now follows the mode when a game starts
or ends while it's open. This replaces the reset button's own aim zone.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

docs/reference.md

@@ -44,7 +44,7 @@ Every screen is an overlay named `frametop.screen.N` with five controls:
 - `.curve` bends the screen into a cylinder around you, using your current distance as the radius, or makes it flat again.
 - `.roll` rolls the screen when you drag it sideways, like a knob. It snaps level within 2.5°, and scrolling on it turns 5° per notch.
 - `.resize`, the tab on the bottom right corner, sets the width. Screens go down to 15 cm wide.
-- `.reset`, left of the bar, puts every screen back in its layout around where you are now, like Meta+Shift+R (`ft-layout apply`). In a VR game, where the screens leave the controllers to the game, aiming a controller at it turns SteamVR's laser on for that button alone, so the trigger clicks it; the game gets the controllers back half a second after you aim away.
+- `.reset`, left of the bar, puts every screen back in its layout around where you are now, like Meta+Shift+R (`ft-layout apply`).
 
 The controls are sized from both the screen's width and its distance from you, follow the surface of a curved screen, and stay invisible until a laser or the 3D mouse's cursor lands on one or comes within about 1.5 times a button's size of it. While invisible they're still there, fully transparent, so SteamVR's laser can find them. They're translucent until a laser is on them, like SteamVR's own window controls.
 
@@ -62,7 +62,7 @@ The Visibility & pins tab of Frametop Display Settings decides when the screens
 In the last three modes the hotkey shows the screens anyway. A screen can also be hidden on its own (Screens shown on the same tab, or `ft-layout hide N`): it stays hidden whatever the mode or the hotkey says, until it's shown again there. Windows on it stay put, and a new window that would open on it floats instead (ft-floatd). Profiles use this to show only some screens. Two more settings on the same tab cover VR games, which ft-screens detects as SteamVR scene apps:
 
 - During VR games, the Always mode hides the screens unless the dashboard is open (the default), or leaves them up.
-- Controllers on the screens. Visible screens can keep SteamVR's laser mouse on, so controllers work them with the dashboard closed, but that also takes the controllers away from a game. By default this is off while a VR game runs, and the 3D mouse or the dashboard works the screens. The other choices are always on, or only with the dashboard open, which also suits flatscreen games since they aren't scene apps.
+- Controllers on the screens. Visible screens can keep SteamVR's laser mouse on, so controllers work them with the dashboard closed, but that also takes the controllers away from a game. By default this is off while a VR game runs, and the 3D mouse or the dashboard works the screens. Pointing a controller at a screen, a floating window, or the keyboard still turns its laser on, like SteamVR's own floating windows, and pointing away gives the game the controllers back. The other choices are always on, or only with the dashboard open, which also suits flatscreen games since they aren't scene apps.
 
 Input from the lasers reaches KWin through ft-screens' own seat. Keys come from the input relay, from pass-through keyboards and any key a pointer device passes through. Typing follows your last click: after a click on a screen it goes to the desktop, even with the SteamVR dashboard open, and after a mouse click on any other panel (the dashboard, Steam, an app like Spotify) it goes there instead. While it goes to the desktop, the relay grabs pass-through keyboards so gamescope, which reads every keyboard itself, doesn't type them into the Steam app too. A program that watches every keyboard for a hotkey loses a grabbed one; with `SHARE_KEYS=1` in `~/.config/frametop.conf`, their keys also go to `@frametop_keys` for it. That's off by default, since any local process that binds the name first would get everything typed into the desktop. Hidden screens don't take typing.